| パートいいえ | メーカー | アプリケーション |
|---|
| MAX7412EPA | MAXIMIC | 5th-order, lowpass, elliptic, switched-capacitor filter. Transition ratio r = 1.6, operating voltage +3V |
| MAX6320PUK27AW-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 2.700V, reset timeout(min) 1ms, watchdog timeout(typ) 6.3ms |
| MAX4566CSE | MAXIMIC | Two dual SPST switches, low-voltage, bidirectional RF/video switch. |
| MAX709SCSA | MAXIMIC | Power-supply monitor with reset. Reset threshold voltage 2.93V |
| MAX4020ESD | MAXIMIC | Low-cost, high-speed, SOT23, single-supply op amp with Rail-to-Rail output. High speed 150MHz - 3dB bandwidth. Transistor count 362 . |
| MAX6318MHUK29CY-T | MAXIMIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 2.930V, reset timeout(min) 140ms, watchdog timeout(typ) 1.6sec |
| MAX291MJA | MAXIMIC | 8th-order, lowpass, switched-capacitor filter. |
| MAX6356LTUT-T | MAXIMIC | Triple-voltage microprocessor supervisory circuit with manual reset. Reset threshold 4.63V (Vcc5) and 3.08V (Vcc3). Active-low push-pull reset 5V. |
| MAX6316LUK39CW-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 3.900V, min reset timeout 140ms, typ watchdog timeout 6.3ms |
| MAX709RCSA | MAXIMIC | Power-supply monitor with reset. Reset threshold voltage 2.63V |
| MAX3180EUK-T | MAXIMIC | +3V to +5.5V, 1.5Mbps RS-232 receiver. |
| MAX877CSA | MAXIMIC | Step-up/step-down DC-DC converters |
| MAX488EEPA | MAXIMIC | +-15kV ESD-protected, low-power, RS-485/RS-422 transceiver. Full-duplex. Data rate 0.25Mbps. Slew-rate limited - yes. Low-power shutdown - no. Receiver/driver enable - no. Quiescent current - 120 microA. Number of transmitter on bus - 32. |
| MAX6317HUK36CY-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.600V, min reset timeout 140ms, typ watchdog timeout 1.6sec |
| MAX6378XR36-T | MAXIMIC | Ultra-low-power voltage detector, 3.6V |
| MAX817MCSA | MAXIMIC | +5V microprocessor supervisory circuit. Reset threshold 4.40V, active-low reset, backup-battery switchover, power-fail comparator, watchdog input, battery freshness seal. |
| MAX4548EAX | MAXIMIC | Serrially controlled, triple 3x2 audio/video crosspoint switches. |
| MAX6320PUK39BY-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 3.900V, reset timeout(min) 20ms, watchdog timeout(typ) 1.6sec |
| ICL7665BCPA | MAXIMIC | Microprocessor voltage monitor with dual overvoltage and undervoltage detection |
| MAX1270BENG | MAXIMIC | Multirange, +5V, 8-channel, serial 12-bit ADC. INL(LSB) +1,-1 |
| MAX6318LHUK30CX-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 3.000V min, reset timeout 140ms, typ watchdog timeout 102ms |
| MAX182BEPI | MAXIMIC | Calibrated 4-channel 12-bit ADC with T/H and reference. |
| MX7524J/D | MAXIMIC | CMOS 8-bit buffered multiplying DAC. TTL/CMOS compatible at +5V. Error +-1/2 LSB |
| MAX860IUA | MAXIMIC | 50mA, Frequency-selectable, switched-capacitor voltage coverter. Input voltage +1.5V to 5.5V, 200microA quiescent current. |
| MAX6364HUT44-T | MAXIMIC | Low-power microprocessor supervisory circuit with auxiliary adjustable reset input. Reset threshold(typ) 4.38V. Active-high push-pull reset. |
| MAX332MJE | MAXIMIC | Quad SPST CMOS analog switch. |
| MAX6319MHUK30C-T | MAXIMIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.000V, reset timeout(min) 140ms |
| MAX4256ESA | MAXIMIC | Single, single-supply operation +2.4V to 5.5V, low-noise, low-distortion, Rail-to-Rail op amp. Gain bandwidth 22MHz, min stable gain 10V/V, with shutdown. |
| MX7821KR | MAXIMIC | 660ns microprocessor-compatible, 8-bit ADC with track/hold. |
| MAX1249BCEE | MAXIMIC | +2.7V to 5.25V, low-power, 4-channel, serial 10-bit ADC. INL (LSB) +1,-1 |
