| パートいいえ | メーカー | アプリケーション |
|---|
| MAX6317HUK38AW-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.800V, min reset timeout 1ms, typ watchdog timeout 6.3ms |
| MAX6316LUK28CZ-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 2.800V, min reset timeout 140ms, typ watchdog timeout 25.6sec |
| MAX4508MJE | MAXIMIC | Fault-protected, high-voltage single 8-to-1 multiplexer. |
| MAX3235ECWP | MAXIMIC | +-15kV ESD-protected, 1microA, 250kbps, 5.0V, dual RS-232 with internal capacitor. |
| MAX182ACWI | MAXIMIC | Calibrated 4-channel 12-bit ADC with T/H and reference. |
| MAX3680EAI | MAXIMIC | 622Mbps, +3.3V, SDH/SONET 18 deserializer with TTL outputs. |
| MAX3864D | MAXIMIC | +3 to +5.5 V, 2.5 Gbp wide dynamic range transimpedance preamplifier |
| MX7828TQ | MAXIMIC | CMOS, high-speed, 8-bit ADC with multiplex. Error (LSB) +-1 |
| MAX6336US23D2-T | MAXIMIC | Ultra-low-voltage, low-power microprocessor circuit with manual reset (reset output active-low, push/pull . Reset threshold(typ) 2.3V, reset timeout(min) 20ms. |
| MAX6310UK32D1-T | MAXIMIC | Multiple-input, programmable reset IC(push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,negative overvoltage reset input).Factory-trimmed reset thresholds 3.120(min),3.280(max). Nominal timeout period 1ms. |
| MAX469EWE | MAXIMIC | Two-channel, triple video buffer. Voltage gain 2V/V. |
| MAX500BEWE | MAXIMIC | CMOS, quad, serial-interface 8-bit DAC. Error(LSB) +-2. |
| MAX6502CMP055-T | MAXIMIC | Low-cost, +2.7V to +5.5V micropower temperature switch. Output stage push-pull. Standard temperature threshold(C) +55. |
| MAX803MEXR-T | MAXIMIC | Microprocessor reset circuit Reset threshold 4.38V. Open-drain active-low reset. 2.5k increments. |
| MAX8868C/D30 | MAXIMIC | Low-noise, low-dropout, 150mA linear regulator with auto-discharge function. Preset output voltage 3.00V |
| MAX4275BJESA | MAXIMIC | Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 49, 1+ (Rf/Dg) noninverting gain 50, -3dB BW 310kHz. |
| MAX6322HPUK27A-T | MAXIMIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 2.700V, reset timeout(min) 1ms |
| MAX483EEPA | MAXIMIC | +-15kV ESD-protected, low-power, RS-485/RS-422 transceiver. Half-duplex. Data rate 0.25Mbps. Slew-rate limited - yes. Low-power shutdown - yes. Receiver/driver enable - yes. Quiescent current - 120 microA. Number of transmitter on bus - 32. |
| MAX491ESD | MAXIMIC | Low-power, slew-rate-limited RS-485/RS-422 transceiver. Full-duplex. Data rate 2.5Mbps. Slew-rate limited - no. Low-power shutdown - no. Receiver/driver enable - yes. Quiescent current - 300 microA. Number of transmitter on bus - 32. |
| MAX6320PUK43CX-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 4.300V, reset timeout(min) 140ms, watchdog timeout(typ) 102ms |
| MAX322EPA | MAXIMIC | Precision, dual-supply, SPTS analog switch. |
| MXD1005PD200 | MAXIMIC | 5-tap silicon delay line |
| MAX4053ACPE | MAXIMIC | Low-voltage, CMOS analog switch |
| DS1859B-020 | MAXIMIC | Dual, temperature-controlled resistors with internally calibrated monitors, 20KOhm |
| MAX6375UR30-T | MAXIMIC | Ultra-low-power voltage detector, 3.0V |
| MAX1480BEPI | MAXIMIC | Complete, isolated RS-485/RS-422 data inteface. |
| MX536AJD | MAXIMIC | 1V. Auxiliary dB output 60dB range. Low power 1.2mA(typ). |
| MAX6319LHUK29A-T | MAXIMIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-low,push/pull and active-high, push/pull).Factory-trimmed reset threshold(typ) 2.930V, reset timeout(min) 1ms |
| MAX6310UK41D4-T | MAXIMIC | Multiple-input, programmable reset IC(push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,negative overvoltage reset input).Factory-trimmed reset thresholds 3.998(min),4.203(max). Nominal timeout period 1120ms. |
| MAX233EPP | MAXIMIC | +5V-powered, multichannel RS-232 driver-receiver. |
