| パートいいえ | メーカー | アプリケーション |
|---|
| MAX4606CPE | MAXIMIC | Low on-resistance (5om max), quad, SPST, CMOS analog switches (two NO and two NC switches). |
| MAX3212EWI | MAXIMIC | +2.7V to 3.6V-powered, 1microA supply current, 3-driver/5-receiver, true RS-232 transceiver. |
| MAX6316LUK29CY-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset, standard version (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 2.930V, min reset timeout 140ms, typ watchdog timeout 1.6sec |
| MAX6379UR34-T | MAXIMIC | Ultra-low-power voltage detector, 3.4V |
| MAX6316MUK41CX-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 4.100V, min reset timeout 140ms, typ watchdog timeout 102ms |
| MAX3665E/D | MAXIMIC | 622Mbps, ultra-low-power, 3.3V transimpedance preamplifier for SDH/SONET. |
| MAX156BCWI | MAXIMIC | 4-channel ADC with simultaneous T/Hs and reference. Error +-1 LSB. |
| MX7575KEWN | MAXIMIC | CMOS, microprocessor-compatible, fast conversion time 5 microsec, 8-bit ADC. INL +-1/2 LSB. |
| MAX156AENG | MAXIMIC | 4-channel ADC with simultaneous T/Hs and reference. Error +-1/2 LSB. |
| MAX6334UR23D3-T | MAXIMIC | Ultra-low-voltage, low power microprocessor reset circuit. Reset threshold(typ) 2.3V, reset timeout(min) 100ms. Standard version |
| MXL1014IN | MAXIMIC | Quad precision op amp. |
| MAX274BCNG | MAXIMIC | 8th-order continuous-time active filter |
| MAX4532EPP | MAXIMIC | Low-voltage, CMOS analog ICs configured as three single-pole/double-throw switch. |
| IH5048ACPE | MAXIMIC | CMOS analog switch. |
| DG390CWE | MAXIMIC | General purpose CMOS dual analog switch. |
| MXD1000SE250 | MAXIMIC | 5-tap silicon delay line |
| DG301CWE | MAXIMIC | Dual, TTL compatible CMOS analog switch. |
| MX7524KCSE | MAXIMIC | CMOS 8-bit buffered multiplying DAC. TTL/CMOS compatible at +5V. Error +-1/4 LSB |
| MAX4119EEE | MAXIMIC | Quad, 270MHz -3dB bandwidth, low-power, current feedback amplifier. |
| MAX6320PUK35BY-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 3.500V, reset timeout(min) 20ms, watchdog timeout(typ) 1.6sec |
| MAX961ESA | MAXIMIC | Single, ultra-high-speed, +3V or +5V, Beyond-the-Rails comparator. Complemehtary output. 270microA shutdown current. Latch enable. |
| ICL7616BMTV | MAXIMIC | Single operational amplifier,5mV |
| MAX148ACPP | MAXIMIC | +2.7V to +5.25V, low-power, 8-channel, serial 10-bit ADC. INL(LSB) +-1/2. |
| MAX6356SYUT-T | MAXIMIC | Triple-voltage microprocessor supervisory circuit with manual reset. Reset threshold 2.93V (Vcc5) and 2.19V (Vcc3). Active-low push-pull reset 5V. Standard version. |
| MAX6806UR23-T | MAXIMIC | Voltage detector. Reset output active-low, push-pull. Threshold reset 2.3V |
| MAX4663EWE | MAXIMIC | 2.5om, quad, SWPST, CMOS analog switch (two NC and two NO switches). |
| MAX971CSA | MAXIMIC | Ultra-low-power, open-drain, single comparator. Internal precision reference 1%. Internal hysteresis yes. |
| MAX497CPE | MAXIMIC | 275MHz -3dB bandwidth, quad closed-loop video buffer, fixed gain +2V/V, 1500V/micros slew rate. |
| MAX2681EUA-T | MAXIMIC | 400MHz to 2.5GHz, low-noise, SiGe downconverter mixer. |
| MAX6322HPUK34D-T | MAXIMIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 3.400V, reset timeout(min) 1120ms |
