| パートいいえ | メーカー | アプリケーション |
|---|
| MAX173CWG | MAXIMIC | Complete 5 microsec CMOS 10-bit A/D converter. |
| MAX631BC/D | MAXIMIC | CMOS fixed +5V output voltage,adjustable output with 2 resistors step-up switching regulator. 10% output accuracy. |
| MAX6318LHUK32BW-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 3.200V min, reset timeout 20ms, typ watchdog timeout 6.3ms |
| MAX4175AMEUK-T | MAXIMIC | Single, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 6, 1+ (Rf/Dg) noninverting gain 7, -3dB BW 640kHz. |
| MAX765ESA | MAXIMIC | -12V or adjustable output from -1V to -16V, high-efficiency, low IQ DC-DC inverter |
| MAX3490EEPA | MAXIMIC | 3.3V-powered, +-15kV ESD-protected, 15Mbps and slew-rate-limited true RS-485/RS-422 transceiver. Guaranteed data rate 12Mbps. Supply voltage 3.0V to 3.6V |
| MAX806SMJA | MAXIMIC | 3.0V or 3.3V microprocessor supervisory circuit. Reset threshold 2.925V. Active-low reset. Manual reset input. Backup-battery switch. Power-fail threshold accuracy +-2%. Power-fail comparator. Reset window +-2% |
| MAX6306UK42D4-T | MAXIMIC | Multiple-input, programmable reset IC (open-drain reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual reset input). Factory-trimmed reset thresholds 4.095(min),4.305(max) Nominal timeout period 1120ms. |
| MAX4074AEESA | MAXIMIC | Micropower, Rail-to-Rail, fixed-gain, single, GainAmp op amp. Inverting gain 1.25V/V, noninverting gain 2.25V/V, -3dB BW 70kHZ. |
| MAX509BEAP | MAXIMIC | Quad, serial 8-bit DAS with Rail-to-Rail output. TUE (LSB) +-1 1/2 |
| MAX4052AEPE | MAXIMIC | Low-voltage, CMOS analog multiplexer |
| MAX901AEPE | MAXIMIC | High-speed, low-power voltage comparator |
| MAX406C/D | MAXIMIC | 1.2microA max, single, single-supply op amp. |
| MAX6317HUK47AW-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 4.700V, min reset timeout 1ms, typ watchdog timeout 6.3ms |
| MAX6376XR23-T | MAXIMIC | Ultra-low-power voltage detector, 2.3V |
| REF02CESA | MAXIMIC | +5V precisioon voltage reference. Max TEMPCO 65ppm/degC. Initial error +-50mV |
| MAX6319MHUK50B-T | MAXIMIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 5.000V, reset timeout(min) 20ms |
| MAX481EPA | MAXIMIC | Low-power, slew-rate-limited RS-485/RS-422 transceiver. Half-duplex. Data rate 2.5Mbps. Slew-rate limited - no. Low-power shutdown - yes. Receiver/driver enable - yes. Quiescent current - 300 microA. Number of transmitter on bus - 32. |
| MAX4252ESA | MAXIMIC | Dual, single-supply operation +2.4V to 5.5V, low-noise, low-distortion, Rail-to-Rail op amp. Gain bandwidth 3MHz, min stable gain 1V/V. |
| MAX6320PUK36AY-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 3.600V, reset timeout(min) 1ms, watchdog timeout(typ) 1.6sec |
| MAX6312UK46D2-T | MAXIMIC | Multiple-input, programmable reset IC(push/pull reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual-reset input). Factory-trimmed reset thresholds 4.514(min) 4.746(max). Nominal timeout period 20ms. |
| MAX3218EPP | MAXIMIC | 1.8V to 4.25V-powered, 1microA supply current RS-232 transceiver with AutoShutdown. |
| MAX6313UK43D3-T | MAXIMIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc, 1 additional undervoltage reset input,negative/overvoltage reset input).Factory-trimmed reset thresholds 4.193(min) 4.408(max).Nominal timeout period 140ms. |
| MAX6318MHUK36BX-T | MAXIMIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.600V, reset timeout(min) 20ms, watchdog timeout(typ) 102ms |
| MAX792TCPE | MAXIMIC | Microprocessor and non-volatile metory supervisory circuit. Reset threshold 3.06V |
| MAX185BMRG | MAXIMIC | High-speed 12-bit A/D converter with external reference input. 10 microsec. max conversion time. Linearity(LSB) +-1. |
| MAX6346XR40-T | MAXIMIC | Microprocessor supervisory circuit (reset output active-low, push-pull). Reset threshold (typ) 4.000V. Order increment 10k |
| MAX159BEUA | MAXIMIC | +2.7V, low-power, 2-channel, 108ksps, serial 10-bit ADC in 8-pin microMAX. INL (LSB) +,- 1 |
| MAX6317HUK48CW-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 4.800V, min reset timeout 140ms, typ watchdog timeout 6.3ms |
| MAX1200AEMH | MAXIMIC | +5V single-supply, 1Msps, 16-bit self-calibrating ADC |
