| パートいいえ | メーカー | アプリケーション |
|---|
| MAX407MJA | MaximIC | 1.2microA max, dual, single-supply op amp. |
| MAX6306UK38D2-T | MaximIC | Multiple-input, programmable reset IC (open-drain reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual reset input). Factory-trimmed reset thresholds 3.705(min),3.895(max) Nominal timeout period 20ms. |
| MAX6310UK42D1-T | MaximIC | Multiple-input, programmable reset IC(push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,negative overvoltage reset input).Factory-trimmed reset thresholds 4.095(min),4.305(max). Nominal timeout period 1ms. |
| MAX805TCPA | MaximIC | 3.0V or 3.3V microprocessor supervisory circuit. Reset threshold 3.075V. Active-high reset. Watchdog input. Backup-battery switch. Power-fail threshold accuracy +-4%. Power-fail comparator. Reset window +-75mV |
| MX7847SQ | MaximIC | Complete, dual, 12-bit multiplying DAC. 12-bit parallel interface. Error (LSB) +-1 |
| MAX6318MHUK46CX-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.630V, reset timeout(min) 140ms, watchdog timeout(typ) 102ms |
| MAX821SUS-T | MaximIC | Microprocessor voltage monitor with pin-selectable power-on reset timeout delay (1ms,max, 20ms,min or 100ms,min). Reset threshold(nom) 2.93V. Active-low reset output. |
| MXD1000SE25 | MaximIC | 5-tap silicon delay line |
| MAX6318LHUK34DW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 3.400V min, reset timeout 1.12sec, typ watchdog timeout 6.3ms |
| MAX188BCCP | MaximIC | Low-power, 8-channel, serial 12-bit ADC. |
| MAX1459C/D | MaximIC | 2-wire, 4-20 mA smart signal conditioner. |
| MAX503ENG | MaximIC | 5V, low-power, parallel-input, voltage-output 10-bit DAC. |
| MAX825TEUK | MaximIC | Microprocessor supervisory circuit. Reset threshold 3.08V. Active-low reset. Active-high reset. Manual reset input. |
| MAX6318LHUK40DX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 4.000V min, reset timeout 1.12sec,typ watchdog timeout 102ms |
| MAX230EPP | MaximIC | +5V-powered, multichannel RS-232 driver-receiver. |
| DG387BWE | MaximIC | General purpose CMOS dual analog switch. |
| MAX3483CPA | MaximIC | 3.3V-powered, 10Mbps and slew-rate-limited true RS-485/RS-422 transceiver. Guaranteed data rate 0.25Mbps. Supply voltage 3.0V to 3.6V |
| ICL8069CMSQ2 | MaximIC | Low-voltage reference, 50 ppm/C - max temp. coefficient. |
| MAX829EUK | MaximIC | Switched-capacitor voltage inverter. 35kHz. +1.5V to +5.5V input voltage range. |
| MAX680C/D | MaximIC | +5V to +-10V voltage converter |
| MAX6160EUS | MaximIC | Low-cost, low-dropout, 3-terminal voltage reference. Preset output voltage adjustable(1.23V to 12.40V). |
| MAX6306UK29D1-T | MaximIC | Multiple-input, programmable reset IC (open-drain reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual reset input). Factory-trimmed reset thresholds 2.857(min),3.000(max) Nominal timeout period 1ms. |
| MAX150BEWP | MaximIC | CMOS highspeed 8-bit A/D converter with reference and track/hold function. Error +,-1 LSB |
| MAX6316MUK49DX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 4.900V, min reset timeout 1120ms, typ watchdog timeout 102ms |
| MAX6322HPUK36A-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 3.600V, reset timeout(min) 1ms |
| MAX164BEWG | MaximIC | CMOS 12-bit A/D converter with track-and-hold. Error +-1 LSB. |
| REF01HP | MaximIC | +10V precisioon voltage reference. Max TEMPCO 25ppm/degC. Initial error +-50mV |
| MAX6314US28D1-T | MaximIC | 68H11/bidirectional-compatible microprocessor reset circuit. Reset threshold(nom) 2.80V. Reset timeout period(min) 1ms. |
| MAX805SEPA | MaximIC | 3.0V or 3.3V microprocessor supervisory circuit. Reset threshold 2.925V. Active-high reset. Watchdog input. Backup-battery switch. Power-fail threshold accuracy +-4%. Power-fail comparator. Reset window +-75mV |
| MAX6307UK27D1-T | MaximIC | Multiple-input, programmable reset IC (open-drain reset output,factory-set reset threshold on Vcc,1additional undervoltage reset input,negative/overvoltage reset inp.).Factory-trimmed reset thresholds2.633(min),2.768(max).Nominal timeout period 1ms. |
