| パートいいえ | メーカー | アプリケーション |
|---|
| MAX505BMRG | MAXIMIC | Quad 8-bit DAC with Rail-to-Rail voltage outputs. Double-buffered logic inputs. TUE +-3/2 LSB. |
| MAX4275BAEUA | MAXIMIC | Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 10, 1+ (Rf/Dg) noninverting gain 11, -3dB BW 560kHz. |
| MAX752CWE | MAXIMIC | Adjustable step-up current-mode DC-DC converter |
| MAX110BC/D | MAXIMIC | Low-cost, 2-channel, 14-bit serial ADC. |
| MAX281AEPA | MAXIMIC | 5th-order, zero-error, bessel lowpass filter. |
| MAX6320PUK29BW-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 2.930V, reset timeout(min) 20ms, watchdog timeout(typ) 6.3ms |
| MXD1005SA75 | MAXIMIC | 5-tap silicon delay line |
| MAX978ESE | MAXIMIC | Quad, single-supply, high-speed, low-power comparator. |
| MAX706REPA | MAXIMIC | Low-cost, microprocessor supervisory circuit. Precison supply-voltage monitor 2.63V. Active-low reset output signal. |
| MAX354CPE | MAXIMIC | Fault-protected analog multiplexer |
| MAX4610ESD | MAXIMIC | Low-voltage, quad, SPST, CMOS analog switches (four NO switches). |
| MAX4420EPA | MAXIMIC | High-speed, 6A single MOSFET driver. 4.5V t0 18V supply range. |
| MAX187BCPA | MAXIMIC | +5V, low-power, 12-bit serial ADC. Error(LSB) +-1. |
| MAX6322HPUK50D-T | MAXIMIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 5.000V, reset timeout(min) 1120ms |
| MAX547BEMH | MAXIMIC | Octal, 13-bit voltage-output DAC with parallel interface. INL(LSBs) +-4. |
| MAX8868C/D32 | MAXIMIC | Low-noise, low-dropout, 150mA linear regulator with auto-discharge function. Preset output voltage 3.15V |
| MAX349MJN | MAXIMIC | Serially controlled, low-voltage, 8-channel multiplexer |
| MAX185BCNG | MAXIMIC | High-speed 12-bit A/D converter with external reference input. 10 microsec. max conversion time. Linearity(LSB) +-1. |
| MAX421EPD | MAXIMIC | +-15V chopper stabilized operational amplifier. |
| MAX205ECPG | MAXIMIC | +-15kV ESD-protected, +5V RS-232 transceiver |
| MAX487C/D | MAXIMIC | Low-power, slew-rate-limited RS-485/RS-422 transceiver. Half-duplex. Data rate 0.25Mbps. Slew-rate limited - yes. Low-power shutdown - yes. Receiver/driver enable - yes. Quiescent current - 120 microA. Number of transmitter on bus - 128. |
| MAX6318MHUK40AZ-T | MAXIMIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.000V, reset timeout(min) 1ms, watchdog timeout(typ) 25.6sec |
| MAX6321HPUK47AW-T | MAXIMIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 4.700V, reset timeout(min) 1ms, watchdog timeout(typ) 6.3ms |
| MAX984CPE | MAXIMIC | Ultra-low-power, open-drain, quad comparator. Internal precision reference 2%. Internal hysteresis no. |
| MAX1662EUB | MAXIMIC | Serial-parallel/parallel-to-serial converter and load-switch controller with SMBus interface |
| MAX742C/D | MAXIMIC | Switch-mode regulator with +5V to +-12V or +-15V dual output. |
| MAX6314US27D4-T | MAXIMIC | 68H11/bidirectional-compatible microprocessor reset circuit. Reset threshold(nom) 2.70V. Reset timeout period(min) 1120ms. |
| MAX6304CPA | MAXIMIC | +5V, low-power microprocessor supervisory circuit with adjustable reset/watchdog (active-high reset, push/pull reset output. |
| MX7578KEWG | MAXIMIC | Calibrated 12-bit A/D converter |
| MAX6312UK31D2-T | MAXIMIC | Multiple-input, programmable reset IC(push/pull reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual-reset input). Factory-trimmed reset thresholds 3.003(min) 3.157(max). Nominal timeout period 20ms. |
